
ATV71HU30N4
Schneider Electric Altivar 71 variable speed drive ATV71, 3kW-480V, EMC filter-graphic terminal.
إظهار المواصفات
Main Characteristics
| Lifecycle status | Discontinued by the manufacturer |
|---|---|
| Range of Product | Altivar 71 |
| Product or Component Type | Variable speed drive |
| Product Specific Application | Complex, high-power machines |
| Component name | ATV71 |
| Motor power kW | 3 kW, 3 phase 380...480 V |
| Maximum motor cable length | 164.04 ft (50 m) shielded cable; 328.08 ft (100 m) unshielded cable |
| Power supply voltage | 380...480 V - 15...10 % |
| Phase | 3 phase |
| Line current | 9 A 480 V 3 phase 3 kW; 10.7 A 380 V 3 phase 3 kW |
| EMC filter | Integrated |
| Assembly style | With heat sink |
| Apparent power | 7 kVA 380 V 3 phase 3 kW |
| Prospective line Isc | 5 kA 3 phase |
| Nominal output current | 6.2 A 4 kHz 460 V 3 phase 3 kW; 7.8 A 4 kHz 380 V 3 phase 3 kW |
| Maximum transient current | 11.7 A 60 s 3 phase 3 kW; 12.9 A 2 s 3 phase 3 kW |
| Output frequency | 0.1…599 Hz |
| Nominal switching frequency | 4 kHz |
| Switching frequency | 1...16 kHz adjustable; 4...16 kHz with derating factor |
| Asynchronous motor control profile | ENA (Energy adaptation) system for unbalanced loads; Voltage/frequency ratio (2 or 5 points); Sensorless flux vector control (SFVC) (voltage or current vector); Flux vector control (FVC) with sensor (current vector) |
| Type of polarization | No impedance Modbus |
Technical Data
| Product destination | Synchronous motors; Asynchronous motors |
|---|---|
| Power supply voltage limits | 323…528 V |
| Power supply frequency | 50...60 Hz - 5...5 % |
| Power supply frequency limits | 47.5...63 Hz |
| Speed range | 1…100 asynchronous motor in open-loop mode, without speed feedback; 1…1000 asynchronous motor in closed-loop mode with encoder feedback; 1…50 synchronous motor in open-loop mode, without speed feedback |
| Speed accuracy | +/- 0.01 % of nominal speed in closed-loop mode with encoder feedback 0.2 Tn to Tn; +/- 10 % of nominal slip without speed feedback 0.2 Tn to Tn |
| Torque accuracy | +/- 15 % in open-loop mode, without speed feedback; +/- 5 % in closed-loop mode with encoder feedback |
| Transient overtorque | 170 % +/- 10 % 60 s every 10 minutes; 220 % +/- 10 % 2 s |
| Braking torque | <= 150 % with braking or hoist resistor; 30 % without braking resistor |
| Synchronous motor control profile | Vector control without speed feedback |
| Regulation loop | Adjustable PI regulator |
| Motor slip compensation | Not available in voltage/frequency ratio (2 or 5 points); Suppressable; Automatic whatever the load; Adjustable |
| Diagnostic | 1 LED (red) for drive voltage |
| Output voltage | <= power supply voltage |
| Insulation | Electrical between power and control |
| Type of cable for mounting in an enclosure | With a NEMA Type1 kit 3 UL 508 cable 104 °F (40 °C), copper 75 °C / PVC; With an IP21 or an IP31 kit 3 IEC cable 104 °F (40 °C), copper 70 °C / PVC; Without mounting kit 1 IEC cable 113 °F (45 °C), copper 70 °C / PVC; Without mounting kit 1 IEC cable 113 °F (45 °C), copper 90 °C / XLPE/EPR |
| Electrical connection | Terminal 2.5 mm², 14 AWG AI1-/AI1+, AI2, AO1, R1A, R1B, R1C, R2A, R2B, LI1...LI6, PWR); Terminal 4 mm², 10 AWG L1/R, L2/S, L3/T, U/T1, V/T2, W/T3, PC/-, PO, PA/+, PA, PB) |
| Tightening torque | 5.3 lbf.in (0.6 N.m) AI1-/AI1+, AI2, AO1, R1A, R1B, R1C, R2A, R2B, LI1...LI6, PWR); 12.4 lbf.in (1.4 N.m), 12.3 lb.in L1/R, L2/S, L3/T, U/T1, V/T2, W/T3, PC/-, PO, PA/+, PA, PB) |
| Supply | Internal supply for reference potentiometer (1 to 10 kOhm) 10.5 V DC +/- 5 %, <10 mA overload and short-circuit protection; Internal supply 24 V DC 21…27 V), <200 mA overload and short-circuit protection |
| Analogue input number | 2 |
| Analogue input type | AI1-/Al1+ bipolar differential voltage +/- 10 V DC 24 V max 11 bits + sign; AI2 software-configurable current 0...20 mA 242 Ohm 11 bits; AI2 software-configurable voltage 0...10 V DC 24 V max 30000 Ohm 11 bits |
| Input sampling time | 2 ms +/- 0.5 ms AI1-/Al1+) - analog; 2 ms +/- 0.5 ms Al2) - analog; 2 ms +/- 0.5 ms LI1...LI5) - discrete; 2 ms +/- 0.5 ms LI6)if configured as logic input - discrete |
| Response time | <= 100 ms in STO (Safe Torque Off); AO1 2 ms +/- 0.5 ms analog; R1A, R1B, R1C 7 ms +/- 0.5 ms discrete; R2A, R2B 7 ms +/- 0.5 ms discrete |
| Absolute accuracy precision | +/- 0.6 % AI1-/Al1+) for a temperature variation 60 °C; +/- 0.6 % AI2) for a temperature variation 60 °C; +/- 1 % AO1) for a temperature variation 60 °C |
| Linearity error | +/- 0.15 % of maximum value AI1-/Al1+, AI2); +/- 0.2 % AO1) |
| Analogue output number | 1 |
| Analogue output type | AO1 software-configurable logic output 10 V 20 mA; AO1 software-configurable current 0...20 mA 500 Ohm 10 bits; AO1 software-configurable voltage 0...10 V DC 470 Ohm 10 bits |
| Discrete output number | 2 |
| Discrete output type | Configurable relay logic R1A, R1B, R1C) NO/NC - 100000 cycles; Configurable relay logic R2A, R2B) NO - 100000 cycles |
| Minimum switching current | 3 mA 24 V DC configurable relay logic |
| Maximum switching current | R1, R2 2 A 250 V AC inductive, cos phi = 0.4; R1, R2 2 A 30 V DC inductive, cos phi = 0.4; R1, R2 5 A 250 V AC resistive, cos phi = 1; R1, R2 5 A 30 V DC resistive, cos phi = 1 |
| Discrete input number | 7 |
| Discrete input type | LI1...LI5 programmable 24 V DC level 1 PLC 3500 Ohm; LI6 switch-configurable 24 V DC level 1 PLC 3500 Ohm; LI6 switch-configurable PTC probe 0…6 1500 Ohm; PWR safety input 24 V DC 1500 Ohm ISO 13849-1 level d |
| Discrete input logic | Negative logic (sink) LI1...LI5), > 16 V, 11 V; Negative logic (sink) LI6)if configured as logic input, > 16 V, 11 V |
| Acceleration and deceleration ramps | Automatic adaptation of ramp if braking capacity exceeded, by using resistor; Linear adjustable separately from 0.01 to 9000 s; S, U or customized |
| Braking to standstill | By DC injection |
| Protection type | Against exceeding limit speed drive; Against input phase loss drive; Break on the control circuit drive; Input phase breaks drive; Line supply overvoltage drive; Line supply undervoltage drive; Overcurrent between output phases and earth drive; Overheating protection drive; Overvoltages on the DC bus drive; Short-circuit between motor phases drive; Thermal protection drive; Motor phase break motor; Power removal motor; Thermal protection motor |
| Insulation resistance | > 1 mOhm 500 V DC for 1 minute to earth |
| Frequency resolution | Analog input 0.024/50 Hz; Display unit 0.1 Hz |
| Communication Port Protocol | Modbus; CANopen |
| Connector type | 1 RJ45 on front face)Modbus; 1 RJ45 on terminal)Modbus; Male SUB-D 9 on RJ45CANopen |
| Physical interface | 2-wire RS 485 Modbus |
| Transmission frame | RTU Modbus |
| Transmission rate | 4800 bps, 9600 bps, 19200 bps, 38.4 Kbps Modbus on terminal; 9600 bps, 19200 bps Modbus on front face; 20 kbps, 50 kbps, 125 kbps, 250 kbps, 500 kbps, 1 Mbps CANopen |
| Data format | 8 bits, 1 stop, even parity Modbus on front face; 8 bits, odd even or no configurable parity Modbus on terminal |
| Number of addresses | 1…127 CANopen; 1…247 Modbus |
| Method of access | Slave CANopen |
| Marking | CE |
| Operating position | Vertical +/- 10 degree |
| Height | 10.2 in (260 mm) |
| Depth | 7.4 in (187 mm) |
| Width | 6.1 in (155 mm) |
| Net Weight | 8.8 lb(US) (4 kg) |
| Functionality | Full |
| Specific application | Other applications |
| Option card | Communication card CC-Link; Controller inside programmable card; Communication card DeviceNet; Communication card EtherNet/IP; Communication card Fipio; I/O extension card; Communication card Interbus-S; Interface card for encoder; Communication card Modbus Plus; Communication card Modbus TCP; Communication card Modbus/Uni-Telway; Overhead crane card; Communication card Profibus DP; Communication card Profibus DP V1 |
Environment & Certifications
| Noise level | 54.5 dB 86/188/EEC |
|---|---|
| Dielectric strength | 3535 V DC between earth and power terminals; 5092 V DC between control and power terminals |
| Electromagnetic compatibility | 1.2/50 µs - 8/20 µs surge immunity test level 3 conforming to IEC 61000-4-5; Conducted radio-frequency immunity test level 3 conforming to IEC 61000-4-6; Electrical fast transient/burst immunity test level 4 conforming to IEC 61000-4-4; Electrostatic discharge immunity test level 3 conforming to IEC 61000-4-2; Radiated radio-frequency electromagnetic field immunity test level 3 conforming to IEC 61000-4-3; Voltage dips and interruptions immunity test conforming to IEC 61000-4-11 |
| Standards | IEC 61800-5-1; IEC 60721-3-3 class 3C1; IEC 61800-3 environments 1 category C2; IEC 61800-3 environments 2 category C2; UL Type 1; EN 55011 class A group 1; IEC 61800-3; IEC 60721-3-3 class 3S2 |
| Product Certifications | UL; GOST; NOM 117; CSA; C-tick |
| Pollution degree | 2 IEC 61800-5-1 |
| IP degree of protection | IP20 |
| Vibration resistance | 1 gn (f= 13…200 Hz) conforming to IEC 60068-2-6; 1.5 mm peak to peak (f= 3…13 Hz) conforming to IEC 60068-2-6 |
| Shock resistance | 15 gn 11 ms IEC 60068-2-27 |
| Relative humidity | 5…95 % without condensation IEC 60068-2-3; 5…95 % without dripping water IEC 60068-2-3 |
| Ambient air temperature for operation | 14…122 °F (-10…50 °C) (without derating) |
| Ambient Air Temperature for Storage | -13…158 °F (-25…70 °C) |
| Operating altitude | <= 3280.84 ft (1000 m) without derating; 3280.84...9842.52 ft (1000...3000 m) with current derating 1 % per 100 m |
Packaging & Logistics
| Nbr. of units in pkg. | 1 |
|---|---|
| Package 1 Height | 12.008 in (30.50 cm) |
| Package 1 Width | 12.2 in (31 cm) |
| Package 1 Length | 15.0 in (38 cm) |
| Package weight(Lbs) | 12.833 lb(US) (5.821 kg) |
| GTIN | 00785901602866 |
Warranty
| Warranty (in months) | 18 |
|---|
يتناسب جيدًا مع
تسليم موثوق للمنتجات الصناعية في جميع أنحاء العالم.
تجربة خالية من المخاطر لمدة 90 يومًا
ضمان لمدة سنتين
شحن وإرجاع مجانيان

ATV71HU30N4
إذا كانت لديك أي أسئلة، فنحن نرحب باتصالك بنا في أي وقت. سنرد عليك في أقرب وقت ممكن، خلال 24 ساعة في أيام الأسبوع.
-
معلومات الشحن
استخدم هذا النص للإجابة على الأسئلة بأكبر قدر ممكن من التفصيل لعملائك.
-
دعم العملاء
استخدم هذا النص للإجابة على الأسئلة بأكبر قدر ممكن من التفصيل لعملائك.
-
الأسئلة الشائعة
استخدم هذا النص للإجابة على الأسئلة بأكبر قدر ممكن من التفصيل لعملائك.
-
اتصل بنا
استخدم هذا النص للإجابة على الأسئلة بأكبر قدر ممكن من التفصيل لعملائك.
الأسئلة الشائعة
يرجى قراءة صفحة الأسئلة الشائعة لمعرفة المزيد.
هل تقومون بتوريد منتجات أصلية؟
نحن نوفر منتجات الأتمتة الصناعية والكهربائية الأصلية من الشركات المصنعة الرائدة بما في ذلك سيمنز (Siemens) وإيه بي بي (ABB) وشنايدر إليكتريك (Schneider Electric) وفينكس كونتاكت (Phoenix Contact) وإيتون (Eaton). أصالة المنتجات وجودتها هي أولويتنا.
هل يمكنني طلب عرض أسعار؟
نعم. إذا لم يتم عرض الأسعار أو كنت بحاجة إلى عناصر متعددة، فما عليك سوى استخدام زر "طلب عرض أسعار" أو الاتصال بفريق المبيعات لدينا للحصول على عرض أسعار مخصص.
هل تشحنون دوليًا؟
نعم. نحن نوفر خدمة الشحن إلى جميع أنحاء العالم، ويمكننا توصيل المنتجات إلى العملاء في جميع أنحاء أوروبا والشرق الأوسط وآسيا ووجهات دولية أخرى.
هل يمكنك توفير قطع غيار قديمة أو يصعب العثور عليها؟
نعم. نحن متخصصون في توريد مكونات الأتمتة الصناعية التي توقف إنتاجها أو عفا عليها الزمن أو يصعب العثور عليها من خلال شبكة الموردين العالمية لدينا.
ما هي الصناعات التي تخدمونها؟
نحن ندعم العملاء في قطاعات الصناعة والنفط والغاز والطاقة والمرافق ومعالجة المياه والبنية التحتية والأتمتة الصناعية.