
ATV71QC11N4
Schneider Electric Altivar 71Q variable speed drive ATV71Q, 110kW / 150HP, 380...480V, IP20.
Show Specifications
Main Characteristics
| Lifecycle status | Discontinued by the manufacturer |
|---|---|
| Range of product | Altivar 71Q |
| Product or component type | Variable speed drive |
| Product destination | Asynchronous motors; Synchronous motors |
| Product specific application | Complex, high-power machines |
| Assembly style | With heat sink |
| Variant | Reinforced version |
| EMC filter | Integrated |
| Network number of phases | 3 phases |
| [Us] rated supply voltage | 380...480 V - 15...10 % |
| Supply voltage limits | 323…528 V |
| Supply frequency | 50...60 Hz - 5...5 % |
| Network frequency limits | 47.5…63 Hz |
| Motor power kW | 110 kW, 3 phases at 380...480 V |
| Motor power hp | 150 hp, 3 phases at 380...480 V |
| Maximum motor cable length | 100 m shielded cable without motor choke; 200 m unshielded cable without motor choke; 150 m shielded cable with motor choke; 250 m unshielded cable with motor choke |
| Line current | 202 A for 380 V 3 phases 110 kW / 150 hp; 163 A for 480 V 3 phases 110 kW / 150 hp |
Technical Data
| Apparent power | 133 kVA at 380 V 3 phases 110 kW / 150 hp |
|---|---|
| Prospective line Isc | 35 kA for 3 phases |
| Continuous output current | 215 A at 2.5 kHz, 380 V - 3 phases; 215 A at 2.5 kHz, 460 V - 3 phases |
| Maximum transient current | 323 A for 60 s, 3 phases; 355 A for 2 s, 3 phases |
| Speed drive output frequency | 0.1…500 Hz |
| Nominal switching frequency | 2.5 kHz |
| Switching frequency | 2...8 kHz adjustable; 2.5...8 kHz with derating factor |
| Speed range | 1…100 for asynchronous motor in open-loop mode, without speed feedback; 1…50 for synchronous motor in open-loop mode, without speed feedback; 1…1000 for asynchronous motor in closed-loop mode with encoder feedback |
| Speed accuracy | +/- 0.01 % of nominal speed in closed-loop mode with encoder feedback 0.2 Tn to Tn; +/- 10 % of nominal slip without speed feedback 0.2 Tn to Tn |
| Torque accuracy | +/- 5 % in closed-loop mode with encoder feedback; +/- 15 % in open-loop mode, without speed feedback |
| Transient overtorque | 170 % of nominal motor torque +/- 10 % for 60 s; 220 % of nominal motor torque +/- 10 % for 2 s |
| Braking torque | 30 % without braking resistor; <= 150 % with braking or hoist resistor |
| Asynchronous motor control profile | Voltage/frequency ratio - Energy Saving, quadratic U/f; Flux vector control without sensor, standard; Flux vector control without sensor, 2 points; Voltage/frequency ratio, 5 points; Voltage/frequency ratio, 2 points; Flux vector control without sensor, ENA (energy Adaptation) system; Flux vector control with sensor, standard |
| Synchronous motor control profile | Vector control with sensor, standard; Vector control without sensor, standard |
| Regulation loop | Adjustable PI regulator |
| Motor slip compensation | Automatic whatever the load; Not available in voltage/frequency ratio (2 or 5 points); Suppressable; Adjustable |
| Local signalling | 1 LED (red) for drive voltage |
| Output voltage | <= power supply voltage |
| Isolation | Electrical between power and control |
| Type of cable | Without mounting kit: 1 wire(s)IEC cable at 45 °C, copper 90 °C / XLPE/EPR; Without mounting kit: 1 wire(s)IEC cable at 45 °C, copper 70 °C / PVC; With an IP21 or an IP31 kit: 3 wire(s)IEC cable at 40 °C, copper 70 °C / PVC; With a NEMA Type1 kit: 3 wire(s)UL 508 cable at 40 °C, copper 75 °C / PVC |
| Electrical connection | Terminal 2.5 mm² / 14 AWG (AI1-/AI1+, AI2, AO1, R1A, R1B, R1C, R2A, R2B, LI1...LI6, PWR); Terminal 2 x 100 mm² (L1/R, L2/S, L3/T, U/T1, V/T2, W/T3); Terminal 2 x 150 mm² (PC/-, PO, PA/+); Terminal 60 mm² (PA, PB) |
| Tightening torque | 24 N.m, 212 lb.in (L1/R, L2/S, L3/T, U/T1, V/T2, W/T3); 41 N.m, 360 lb.in (PC/-, PO, PA/+); 12 N.m, 106 lb.in (PA, PB); 0.6 N.m (AI1-/AI1+, AI2, AO1, R1A, R1B, R1C, R2A, R2B, LI1...LI6, PWR) |
| Supply | Internal supply for reference potentiometer (1 to 10 kOhm): 10.5 V DC, +/- 5 %, <10 mA with overload and short-circuit protection; Internal supply: 24 V DC (21…27 V), <200 mA with overload and short-circuit protection |
| Analogue input number | 2 |
| Analogue input type | AI2 software-configurable voltage: 0...10 V DC 24 V max, impedance: 30000 Ohm, resolution 11 bits; AI1-/Al1+ bipolar differential voltage: +/- 10 V DC 24 V max, resolution 11 bits + sign; AI2 software-configurable current: 0...20 mA, impedance: 242 Ohm, resolution 11 bits |
| Sampling duration | 2 ms +/- 0.5 ms (LI6)if configured as logic input - discrete input; 2 ms +/- 0.5 ms (LI1...LI5) - discrete input; 2 ms +/- 0.5 ms (AI1-/Al1+) - analog output; 2 ms +/- 0.5 ms (Al2) - analog output |
| Accuracy | +/- 0.6 % (AI1-/Al1+) for a temperature variation 60 °C; +/- 0.6 % (AI2) for a temperature variation 60 °C; +/- 1 % (AO1) for a temperature variation 60 °C |
| Linearity error | +/- 0.15 % of maximum value (AI1-/Al1+, AI2); +/- 0.2 % (AO1) |
| Analogue output number | 1 |
| Analogue output type | AO1 software-configurable voltage: 0...10 V DC, impedance: 470 Ohm, resolution 10 bits; AO1 software-configurable current: 0...20 mA, impedance: 500 Ohm, resolution 10 bits; AO1 software-configurable logic output 10 V 20 mA |
| Discrete output number | 2 |
| Discrete output type | Configurable relay logic: (R1A, R1B, R1C) NO/NC - 100000 cycles; Configurable relay logic: (R2A, R2B) NO - 100000 cycles |
| Response time | R1A, R1B, R1C 7 ms, tolerance +/- 0.5 ms; R2A, R2B 7 ms, tolerance +/- 0.5 ms; AO1 2 ms, tolerance +/- 0.5 ms; <= 100 ms in STO (Safe Torque Off) |
| Minimum switching current | 3 mA at 24 V DC for configurable relay logic |
| Maximum switching current | 5 A at 250 V AC on resistive load - cos phi = 1 - L/R = 0 ms (R1, R2); 5 A at 30 V DC on resistive load - cos phi = 1 - L/R = 0 ms (R1, R2); 2 A at 250 V AC on inductive load - cos phi = 0.4 - L/R = 7 ms (R1, R2); 2 A at 30 V DC on inductive load - cos phi = 0.4 - L/R = 7 ms (R1, R2) |
| Discrete input number | 7 |
| Discrete input type | LI1...LI5: programmable 24 V DC with level 1 PLC, impedance: 3500 Ohm; LI6: switch-configurable 24 V DC with level 1 PLC, impedance: 3500 Ohm; LI6: switch-configurable PTC probe 0…6, impedance: 1500 Ohm; PWR: safety input 24 V DC, impedance: 1500 Ohm conforming to ISO 13849-1 level d |
| Discrete input logic | Positive logic (source) (LI6)if configured as logic input, 11 V (state 1); Negative logic (sink) (LI6)if configured as logic input, > 16 V (state 0), 11 V (state 1); Negative logic (sink) (LI1...LI5), > 16 V (state 0), 17 V (state 1) |
| Acceleration and deceleration ramps | S, U or customized; Linear adjustable separately from 0.01 to 9000 s; Automatic adaptation of ramp if braking capacity exceeded, by using resistor |
| Braking to standstill | By DC injection |
| Protection type | Overheating protection: drive; Thermal protection: drive; Short-circuit between motor phases: drive; Input phase breaks: drive; Overcurrent between output phases and earth: drive; Overvoltages on the DC bus: drive; Break on the control circuit: drive; Against exceeding limit speed: drive; Line supply undervoltage: drive; Line supply overvoltage: drive; Against input phase loss: drive; Thermal protection: motor; Motor phase break: motor; Power removal: motor |
| Dielectric strength | 3535 V DC between earth and power terminals; 5092 V DC between control and power terminals |
| Insulation resistance | > 1 mOhm 500 V DC for 1 minute to earth |
| Frequency resolution | Display unit: 0.1 Hz; Analog input: 0.024/50 Hz |
| Communication port protocol | Modbus; CANopen |
| Connector type | 1 RJ45 (on front face) for Modbus; 1 RJ45 (on terminal) for Modbus; 1 RJ45 for CANopen |
| Physical interface | 2-wire RS 485 for Modbus |
| Transmission frame | RTU for Modbus |
| Transmission rate | 9600 bps, 19200 bps for Modbus on front face; 4800 bps, 9600 bps, 19200 bps, 38.4 Kbps for Modbus on terminal; 20 kbps, 50 kbps, 125 kbps, 250 kbps, 500 kbps, 1 Mbps for CANopen |
| Data format | 8 bits, 1 stop, even parity for Modbus on front face; 8 bits, odd even or no configurable parity for Modbus on terminal |
| Type of polarization | No impedance for Modbus |
| Number of addresses | 1…247 for Modbus; 1…127 for CANopen |
| Method of access | Slave CANopen |
| Type of cooling | Water cooled |
| Cooling fluid type | Clean water; Water-glycol mixture; Industrial water |
| Operating temperature water | 5…55 °C |
| Thermal losses | 2100 W 100 % of line current for area of liquid cooling (power part); 490 W 100 % of line current for area of air cooling (control part) |
| Flow velocity | 8 |
| Pressure drop | 1.5 bar |
| Volume of cooling water | 0.2 l |
| Operating position | Vertical +/- 10 degree |
| Net weight | 80 kg |
| Option card | Communication card for Modbus TCP; Communication card for Fipio; Communication card for Modbus/Uni-Telway; Communication card for Modbus Plus; Communication card for EtherNet/IP; Communication card for DeviceNet; Communication card for Profibus DP; Communication card for Profibus DP V1; Communication card for Interbus-S; Communication card for CC-Link; Interface card for encoder; I/O extension card; Controller inside programmable card; Overhead crane card |
| Width | 330 mm |
| Height | 950 mm |
| Depth | 377 mm |
Environment & Certifications
| Ambient air temperature for operation | -10…50 °C (without derating) |
|---|---|
| Ambient air temperature for storage | -25…70 °C |
| Operating altitude | <= 1000 m without derating; 1000...3000 m with current derating 1 % per 100 m |
| Electromagnetic compatibility | Electrostatic discharge immunity test level 3 conforming to IEC 61000-4-2; Radiated radio-frequency electromagnetic field immunity test level 3 conforming to IEC 61000-4-3; Electrical fast transient/burst immunity test level 4 conforming to IEC 61000-4-4; 1.2/50 µs - 8/20 µs surge immunity test level 3 conforming to IEC 61000-4-5; Conducted radio-frequency immunity test level 3 conforming to IEC 61000-4-6; Voltage dips and interruptions immunity test conforming to IEC 61000-4-11 |
| Pollution degree | 2 conforming to EN/IEC 61800-5-1; 3 conforming to UL 840 |
| IP degree of protection | IP00 conforming to EN/IEC 61800-5-1; IP00 conforming to EN/IEC 60529; IP41 on upper part conforming to EN/IEC 61800-5-1; IP41 on upper part conforming to EN/IEC 60529; IP30 on the front panel conforming to EN/IEC 61800-5-1; IP30 on the front panel conforming to EN/IEC 60529; IP30 on side parts conforming to EN/IEC 61800-5-1; IP30 on side parts conforming to EN/IEC 60529; IP54 on lower part conforming to EN/IEC 61800-5-1; IP54 on lower part conforming to EN/IEC 60529 |
| Vibration resistance | 1.5 mm peak to peak (f= 3…10 Hz) conforming to EN/IEC 60068-2-6; 0.6 gn (f= 10…200 Hz) conforming to EN/IEC 60068-2-6 |
| Shock resistance | 7 gn for 11 ms conforming to EN/IEC 60068-2-27 |
| Relative humidity | 5…95 % without condensation conforming to IEC 60068-2-3; 5…95 % without dripping water conforming to IEC 60068-2-3 |
| Noise level | 69.5 dB conforming to 86/188/EEC |
| Standards | IEC 60721-3-3 class 3C2; EN 61800-3 environments 1 category C3; IEC 61508 SIL2; ISO 13849-1 level d; EN/IEC 61800-5-1; EN 61800-3 environments 2 category C3; EN/IEC 61800-3; EN 55011 class A group 2; UL Type 1 |
| Product certifications | CSA; C-Tick; NOM 117; UL; GOST |
| Marking | CE |
Packaging & Logistics
| Number of Units in Package 1 | 1 |
|---|---|
| Package 1 Height | 53.0 cm |
| Package 1 Width | 38.0 cm |
| Package 1 Length | 129.0 cm |
| Package 1 Weight | 95.0 kg |
Warranty
| Warranty (in months) | 18 |
|---|
Pairs well with
Worldwide delivery, dispatched from Erbil
Technical support before and after you order
Genuine parts from authorised manufacturers
Obsolete and hard-to-find items sourced

ATV71QC11N4
If you have any questions, you are always welcome to contact us. We'll get back to you as soon as possible, within 24 hours on weekdays.
-
Shipping
We ship worldwide from our warehouse in Erbil, Iraq, and deliver across Baghdad and all governorates. Stocked lines dispatch quickly; items sourced to order have their lead time confirmed in writing with your quote.
-
Technical support
Not sure which part you need, or whether an alternative is compatible? Send us the part number, the equipment it goes into, or a photo of the nameplate and our team will confirm the correct item before you order.
WhatsApp +964 781 287 9696 or sales@alnajahpower.com.
-
Pricing and quotes
Prices are not shown online because they depend on quantity, specification and current availability. Add the items you need to your quote list and send it — we reply within one business day with pricing and lead time.
-
Contact us
Alnajah Power
Makhmur Str. 83, Erbil 44020, IraqPhone / WhatsApp: +964 781 287 9696
sales@alnajahpower.comSaturday to Thursday, 09:00 – 18:00.
FAQs
Please read our FAQs page to find out more.
Do you supply genuine products?
We supply genuine industrial automation and electrical products from leading manufacturers including Siemens, ABB, Schneider Electric, Phoenix Contact, and Eaton. Product authenticity and quality are our priority.
Can I request a quotation?
Yes. If pricing is not displayed or you require multiple items, simply use the “Request a Quote” button or contact our sales team for a customized quotation.
Do you ship internationally?
Yes. We provide worldwide shipping and can deliver products to customers across Europe, the Middle East, Asia, and other international destinations.
Can you source obsolete or hard-to-find parts?
Yes. We specialize in sourcing discontinued, obsolete, and difficult-to-find industrial automation components through our global supplier network.
What industries do you serve?
We support customers in manufacturing, oil & gas, energy, utilities, water treatment, infrastructure, and industrial automation sectors.